An overview of how Cerazorb is attached to a cement slab prior to tile setting. Instruction on how to install Cerazorb under LVT/VCT and vinyl. Here's an email from Impacta concerning roller weight: Jamie Vallee 9:39 AM (25 minutes ago) to me A 100lb roller is fine. The min is 35lbs. Hope this helps. Thanks, Jamie Vallee Product Manager Sound Seal / Impacta Flooring Division 50 H.P. Almgren Dr Agawam, MA 01001 Phone: 413-789-1770 ext 135 Fax: 413-789-2248 Email: firstname.lastname@example.org Web: www.soundseal.com
Surface must be structurally sound, clean, dry and free from dirt, oil sealers or any contaminants that would prevent a good bond. CeraZorb must acclimatize in their sealed packaging for 48 hours at a temperature of 65 degrees.
Inspect concrete sub floor for any open cracks and fill with a high grade patch. Remove any excess concrete lumps or residue that may interfere with the installation of CeraZorb. The concrete slab should be fully cured, dry, smooth, flat, and accept water penetration. Concrete must be free of efflorescence and not subject to hydrostatic pressure. A good quality concrete waterproof sealer may be required if moisture in the slab is above 10%.
1. CeraZorb can be bonded to the sub floor with Impacta T-440 bond coat adhesive. Use a 1/16” x 1/16” x 1/16” square-notched trowel. Apply only enough adhesive as can be covered by a 4’ x 4’ sheet. Clean up any extra before the adhesive skins over. Impacta T-440 and the sub floor must be at 65ºF (18ºC). Armstrong S-235 Multi-Purpose Adhesive. is OK according to Soundseal. Roberts 6700 Indoor and Outdoor Carpet Adhesive Is also OK.
2. CeraZorb can be bonded to the sub floor with Mapei Ultracontact or UltracontactRS bond coat adhesive or any high quality latex/polymer modified thin-set (recommended, but not sold through WarmlyYours). Use a 1/8” x 1/8” x 1/16” V-Notched trowel. Apply
only enough adhesive as can be covered by a 2’ x 4’ sheet. Clean up any extra adhesive before the adhesive skins over. Mapei Ultracontact or UltracontactRS and the sub floor must be at 65ºF (18ºC).
Set the CeraZorb into the adhesive while it is still wet.
Do not allow adhesive to skin over. Lift a corner periodically to see if the adhesive is transferring 100%. If adhesive is not transferring, apply additional adhesive. Flat trowel the CeraZorb to smooth out air pockets. Continue to install CeraZorb sheets making sure to install with edges butted tight to each other, do not overlap seams. After first row is completed, roll the mat with a 50 lb roller. Install second row with staggered seams to the first row and repeat steps above. It is recommended to wait 8-12 hours before installing tile on top of CeraZorb.
Can pressure sensitive adhesives be used to stick down the CeraZorb? Yes, all pressure-sensitive adhesives are fine. The tech from Impacta even said they used double sided tape at a tradeshow a few weeks back and that worked fine.
Can LVT and VCT go directly onto the surface of CeraZorb? --NO. Put a skim coat of SLC, or even plywood over it first. Then, LVT/VCT can be installed.
Content taken from Cerazorb installation instructions at this web address:
Added by AISA 4/6:
MAPEI recommended Primer-T for priming Cerazorb, when using SLC over it. When using Primer-T apply it undiluted. Add no water; no mixing is required.