PRO-Tect Self-Regulating Heat Tape for Pipes — 250 ft, 5 W/ft, 120V
This support page provides publications, manuals, specifications, videos, support articles, and common support questions
Notices
Quebec Repairability Notice
Avis important pour les consommateurs du Québec:
WarmlyYours n'offre pas de services de réparation ni de pièces de rechange pour ce produit. Plus précisément, la fiche intégrée et l'élément chauffant ne sont pas offerts comme pièces de rechange. Si votre produit de protection contre le gel des tuyaux ou ruban chauffant tombe en panne pendant la période de garantie, nous remplacerons l'unité complète conformément à notre politique de garantie. Notre équipe d'assistance technique est disponible 24h/24 et 7j/7 par téléphone pour toute aide à l'installation ou au dépannage. Pour plus de détails, consultez notre politique de retour. Cet avis est fourni conformément à la Loi sur la protection du consommateur du Québec, article 39 (telle qu'amendée en 2025).
Important Notice for Québec Consumers:
WarmlyYours does not provide repair services or replacement parts for this product. Specifically, the built-in plug and the heating element are not available as replacement parts. If your pipe freeze protection or heat tape product fails within the warranty period, we will replace the entire unit according to our warranty policy. Our technical support team is available 24/7 by phone for installation and troubleshooting assistance. For full details, see our Return Policy. This notice is provided in accordance with Québec's Consumer Protection Act, section 39 (as amended in 2025).
Support Questions
Showing 10 of 16 questions
Electric-resistance heating cables and systems have no polarity. This includes all current WarmlyYours heating elements.
Heat tape is electrical equipment: improper installation, damaged cable, or misuse can cause fire or electric shock. Select cable approved for your pipe and location, follow its layout and insulation requirements, provide the specified electrical protection, and inspect it before each cold season. Do not use damaged equipment or overlap cable unless the exact product instructions permit it.
Yes, it can be used for both application types to prevent pipes from freezing and bursting during cold weather.
No. They are not designed to be powered by DC voltage. They must be used with AC voltage.
Heat trace, heat tape, or heating cable for pipes is typically an electric heating cable that can be attached to the pipe which helps keep non-flowing water pipes in poorly insulated perimeter walls flowing despite harsh winter temperatures.
Pipe heat tape is intended for freeze prevention, not as a guaranteed way to thaw an already frozen pipe. A frozen pipe may be damaged. Have the plumbing assessed and thawed safely by a qualified professional; never use an open flame. Before future cold weather, verify cable selection, thermostat placement, insulation, and electrical protection.
Cable temperature depends on the product, surrounding conditions, installation, and controls. Do not assume a universal surface-temperature range. Follow the exact cable and pipe manufacturers’ limits, particularly for plastic pipe, and use the specified insulation and thermostat placement.
Pipe heat tape electricity use depends on cable length, power output, run time, and controls. For a fixed-output cable, watts = length in feet × W/ft. A 30-foot, 7 W/ft kit draws 210 watts while energized; eight energized hours uses 1.68 kWh. Multiply by your local rate for cost. Thermostat duty cycle and self-regulating output change actual consumption.
Never spiral heating cable around pipes. Attach self regulating cable in straight runs at the 8 o'clock position, or if two runs are required (pipes greater than 12“ diameter) attach the cable at the 8 o'clock and the 4 o'clock positions. Please refer to the installation manual for further information.
WarmlyYours offers a conversion kit (SR-PLUG-KIT) to enable a plug-in requirement. This kit includes ground fault equipment protection (GFEP). The receptacle must be 120V, grounded, and approved for wet locations if located outside. The self regulating cable must not exceed 140‘ in length.
WarmlyYours does not recommend using an extension cord for permanent installations. Pipe heat should always be plugged directly into a receptacle or hardwired to the circuit that is powering it.
No. It is not listed for this application, and it is not warrantied for use in direct burial or wet applications.
No. Only install pipe heat (heat trace cable) in accessible locations. Do not install this self regulating cable in walls or any place where the cable is hidden. Do not run it through walls, ceilings, or floors. The cable must be installed 10“ away from combustible surfaces, such as wood, and it should not be embedded in insulation or roofing material.
Do not wrap self regulating cable around the pipe in a coiled or spiral fashion, and do not use electric tape to attach it. WarmlyYours recommends attaching the cable in a straight run and to use aluminum or fiberglass tape, pipe straps, or plastic zip ties to attach the cable. Then cover the assembly with fire-resistant insulation and assure it is waterproof. Place electrical heating cable WARNING labels every 10‘, and where the label will be clearly visible.
Use plastic zip ties, aluminum or fiberglass tape, or pipe straps. Do NOT use vinyl electrical tape, masking tape or duct tape. Do NOT use metal wire or metal twist ties to attach the cable.
Ice Shield is 120V or 240V and outputs 5W/ft, and is designed for roof and gutter deicing.
PRO-Tect is 120V or 240V and outputs 5W/ft, 8W/ft, or 10W/ft, and is designed for pipe freeze protection.
Documents
Installation
- Pro Tect Pipe Freeze Protection Self Regulating Heating Cable Install Manual (English)
- SR-PLUG-KIT Plug-in Conversion Kit with Ground Fault Equipment Protection (GFEP) Installation Manual (English)
- Self-Regulating Pipe Freeze Protection PT-DUAL Installation Sheet A (English)
Technical Specifications
- PRO-Tect Pipe Freeze Protection Self Regulating Heating Cable End Seal Termination Kit Spec Sheet (English)
- PRO-Tect Self-Regulating Heat Tape for Pipes In-Line Splice Kit Spec Sheet (English)
- PRO-Tect Self-Regulating Heat Tape for Pipes T-Splice Kit Spec Sheet (English)
Technical Information
Sell Sheets
- PRO-Tect Self-Regulating Heat Tape for Pipes Sell Sheet Canada (English)
- Self-Regulating Pipe Freeze Protection Dual-Zone Control PT-DUAL Sell Sheet (English)
- Self-Regulating Pipe Freeze Protection Single-Zone Control PT-SINGLE Sell Sheet (English)
Operation Manuals
- Self-Regulating Pipe Freeze Protection PT-DUAL Manual (English)
- Self-Regulating Pipe Freeze Protection PT-SINGLE Manual (English)
Project Planners
Specifications
Electrical
| Amps | 10.42 A |
| Benefits | Can be cut-to-length & overlapped |
| Cable Type | Self Regulating |
| Connection Method | Hardwired |
| Power | 5 W/ft. - 120 V |
| Voltage | 120 V |
| Watts Per Ft. at 50°F/10°C | 5 W |
Warranty / Certifications
| Approvals | cULus & cCSAus Listed |
| Warranty | 10 years |
Construction
| Cable Cross Section | 0.42″ x 0.23″ / 10.7mm x 5.84mm |
| Cable Jacket | Waterproof thermoplastic |
Product Dimensions
| Length | 250′ |
| Weight | 20.8 lbs |
Installation
| Maximum Intermittent Exposure Temperature, 1000 Hours (Power On or Off) | 185°F / 85°C |
| Maximum Maintain or Continuous Exposure Temperature (Power On) | 149°F / 65°C |
| Minimum Bend Radius | 1.125″ / 28.6mm |
| Minimum Installation Temperature | 0°F / -18°C |
Identifiers
| SKU | PT-SR-120-05-0250 |
| UPC (GTIN-12) | 881308067854 |
Videos
Articles
Similar Items
Do you need support or specifications for a specific model? Identify your model below.