
Radiant heat travels through air, and typically heats up objects closer to the panel first and then the rest of the room later. Infrared heating from the panel can be easily detected from about 3-4 feet. Ideally, the radiant panel should be aimed onto the area with more use, since that will be the surface that will warm up first.
Need more help? View support options
Yes, they are cTUVus Listed.
Need more help? View support options
Electric-resistance heating cables and systems have no polarity. This includes all current WarmlyYours heating elements.
Need more help? View support options
The power box, where the cord starts, is located at the lower-middle part of the panel (for vertical mount) or left-middle (for horizontal mount). See additional images in the product's image gallery.
Need more help? View support options
Ember Radiant Panel is 24 inches in width and either 35 or 47 inches in length and the average bath towel is 20 -24 inches wide by 40 to 50 inches long. With these dimensions, one towel draped in half over the bar performs best. Two hand towels draped in half would work well too, as hand towels tend to be about 12-15 inches in width.
Need more help? View support options
No, the bar is not heated.
Need more help? View support options
The bar simply being screwed-in to the pre-drilled holes on the back of the panel.
Need more help? View support options
No, the back of the panel has only two pre-drilled locations. One at the upper half of the unit and one at the lower half.
Need more help? View support options
One towel draped in half, or two hand towels draped in half.
Need more help? View support options
We do not recommend controlling these panels with dimmers.
Need more help? View support options
Yes.
Need more help? View support options
Yes.
Need more help? View support options
If you have a room with "average" insulation levels, take the square footage and multiply it by 7 or 8 watts per square foot. That will provide a good estimate of the watts needed to heat that space.
Need more help? View support options
Only the 35" x 24" and 47" x 24" Ember Flex radiant panels (IP-EM-FLX-WHT-0500-CW and IP-EM-FLX-WHT-0700-CW) can be mounted from the ceiling and come with all of the necessary hardware to accomplish this. The 35" x 12" Ember Flex panel and all panels from the Ember Glass and Ember Mirror lines can't be mounted from the ceiling.
Need more help? View support options
The startup heating time for this infrared heating system is approximately 5 to 10 minutes. However, your room will not feel warmer immediately because the cold objects in the room (furniture, walls, ceilings, floors, etc.) need to warm up first. Once these surfaces are heated via infrared heating, the warmth will spread throughout the room.
Need more help? View support options
Radiant panels using infrared heating can get very hot on the surface (up to 275ºF). For safety, it is recommended that your infrared heating system be mounted out of the reach of children.
Need more help? View support options
The heat conductor is carbon fiber pressed in an epoxy ceramic resin.
Need more help? View support options
The power box, where the cord starts, is located at the lower-middle part of the panel (for vertical mount) or left-middle (for horizontal mount). See additional images in the product's image gallery.
Need more help? View support options
Verify 120V power at the connection of the panel to the circuit at the junction box in the wall (for hardwired connections), or at the outlet (for plug-in connections). Each Ember heater has a built-in safety switch that turns off the heating element automatically if it overheats. By unplugging or disconnecting the unit and waiting for about 10 to 15 minutes, the safety switch will reset automatically and the unit will be operational again.
If you experience additional issues, please give us a call at 1-800-875-5285.
Need more help? View support options
Material | Anodized, rustproof aluminum |
SKU | IP-EM-ACC-BAR |
UPC (GTIN-12) | 881308042493 |