To prevent any melting, ensure that the heating wire is at least 4” from the toilet wax ring.
Need more help? View support options
Yes, but any furniture that may trap heat, such as pieces with an enclosed bottom, should be avoided. Furniture on legs with a clearance of at least 3" is permissible.
Need more help? View support options
The subfloor will need to be prepared as per the instructions of the self-leveling cement (SLC) used. Please note that most self-leveling products require the use of a primer as specified by the SLC company.
Need more help? View support options
One thermostat can control multiple heating mats/cables as long as all the heating elements are using less than 15 amps:
TempZone™ will cover aprx. 120 sq. ft. for 120V systems and 240 sq. ft. for 240V systems on one thermostat.
Environ™ will cover aprx. 150 sq. ft. for 120V systems and 300 sq. ft. for 240V systems on one thermostat.
Slab Heat will cover aprx. 90 sq. ft. for 120V systems and 180 sq. ft. for 240V systems on one thermostat.
Need more help? View support options
No. A bathroom floor would be installed in the same way. Our TempZone floor heating systems are wet-location listed and ideal for bathroom floors.
Need more help? View support options
Yes, Luxury Vinyl Tile (LVT) is typically installed over the embedded heating element using self-leveling cement (SLC). Many people choose to use SLC when installing tile over floor heating.
We do not suggest using thinset to encase the heating wires with LVT, as it is very difficult to get thinset completely flat.
Need more help? View support options
We suggest the heating product be embedded in a minimum of 3/8" of self-leveling cement (SLC). Always check with the manufacturer for specific recommendations.
Need more help? View support options
Yes, if the flooring manufacturer recommends this installation method. In most cases, the heating element will still need to be embedded in self-leveling cement before the flooring is installed.
Need more help? View support options
There are heating systems designed for floating floors, such as our Environ system. However, the flooring must be rigid enough so it does not mold itself to the heating cables over time.
Check the flooring manufacturer's floor heating recommendations. In most cases, the heating system will need to be embedded beneath the flooring. Check for all "flatness" requirements for the flooring you choose. The flattest floors utilize self-leveling cement when installed correctly.
Need more help? View support options
Not a good choice for mosaic tile work, Prodeso requires 2“ x 2“ or larger tiles.
Need more help? View support options
Self-Leveling (SLC) Cement is not recommended for use over Prodeso. Contact WarmlyYours if self-leveling underlayment is required.
Need more help? View support options
Prodeso installation membrane does not eliminate the need for expansion joints (adhere to local codes).
Need more help? View support options
Unroll the membrane the day before installation to flatten it and avoid any potential ‘memory’ due to environmental conditions.
Need more help? View support options
Install membrane over entire floor first, then heating cable, then do the tiles 1 or 2 at a time. Never cover the Prodeso entirely with thin-set first. Only apply as much thin-set as needed to lay a couple of tiles at a time.
Need more help? View support options
Waterproofing is recommended under and around tubs/showers. It’s also recommended wherever the tile could possibly be exposed to considerable amounts of water. Prodeso is naturally waterproof, but the corners and seams need to be treated with waterproofing tape and thin-set. (Use Pro WP Waterproofing Band 5“ - Soft polyethylene tape – to seal seams.)
Need more help? View support options
When laying Prodeso installation membranes adjacent to each other, align the square relief pegs for the later heating element cable runs.
Need more help? View support options
1.25"
Need more help? View support options
The wire spacing in the Prodeso Cable Installation Membrane is 3.75“, or every 3rd peg.
Need more help? View support options
Country of Origin (COO) | Italy |
SKU | TC-MEM-BL-BND-0624 |
UPC (GTIN-12) | 881308070441 |
Warranty | 10 years |
Do you need support or specifications for a specific model? Identify your model below.