Contact Us Open

Loading contact options...

Sign In

Loading...
TempZone Cable Kit 235 ft (73.4 sqft @ 3.75 in spacing) with nTrust 2.0 Touch Nonprogrammable Thermostat, Uncoupling Membrane, 240V, 3.7/ft, 3.78A

TempZone Cable Kit 235 ft (73.4 sqft @ 3.75 in spacing) with nTrust 2.0 Touch Nonprogrammable Thermostat, Uncoupling Membrane, 240V, 3.7/ft, 3.78A

Part Number: TCT240-KIT-UTN5-MEM-235
This support page provides publications, manuals, specifications, videos, support articles, and common support questions
Need help? Call our experts at (800) 875-5285
Create a new Support Request
Shop Now
Jump to

Support Questions

Showing 10 of 50 questions

Yes. Unlike the heating cable for electric floor heating, the cold lead wires can be trimmed.

22 people found this helpful Was this helpful? Yes No

To prevent any melting, ensure that the heating wire is at least 4” from the toilet wax ring.

17 people found this helpful Was this helpful? Yes No

When installing electric floor heating over a concrete slab, an insulating underlayment like ThermalSheet is highly recommended to ensure efficient operation, faster heating times and warmer floor temperatures.

15 people found this helpful Was this helpful? Yes No

Yes, but any furniture that may trap heat, such as pieces with an enclosed bottom, should be avoided. Furniture on legs with a clearance of at least 3" is permissible.

15 people found this helpful Was this helpful? Yes No

Electric-resistance heating cables and systems have no polarity. This includes all current WarmlyYours heating elements.

14 people found this helpful Was this helpful? Yes No

When WarmlyYours electric floor heating systems are being installed on a concrete slab, we strongly recommend adding a layer of insulation over the slab prior to installing the system. While our electric floor heating provides up to 25% more heating power per square foot than many of our competitors, the slab will always act as a "heat sink." Some of the heat that would otherwise be transferred to the flooring surface will remain in the slab, causing the floor’s surface temperature to be considerably lower. This is true with any electric radiant floor heating system.

When installed on top of a concrete slab without insulation, it is generally accepted that electric floor heating will take the chill away from the floor and provide a small amount of warmth. Adding insulation on top of the slab and beneath any electric radiant floor heating system will allow a greater percentage of the heat generated to transfer to the flooring surface. This results in greater efficiency and therefore faster warm up times, higher expected surface temperatures and lower energy usage. The floor will have the capacity to warm to a comfortable temperature, and in some cases can be employed as the primary heat source for that room.

The recommended types of insulation are natural cork, insulated tile backer boards and insulated underlayment, such as ThermalSheet™ synthetic cork.

13 people found this helpful Was this helpful? Yes No

The breaker and wire sizes are selected based on the total amperage of the WarmlyYours heating system connected to a single thermostat. This information is on the WarmlyYours heating system's installation plan, electrical plan, or UL label. Based on guidelines from the National Electrical Code: loads up to 16 Amps may utilize 12 gauge wire with a 20-Amp breaker, and loads up to 12 Amps - 14 gauge wire with a 15-Amp breaker. Local code and/or other factors may change these guidelines.

6 people found this helpful Was this helpful? Yes No

WarmlyYours’ 25-Year No Nonsense™ Warranty is the most comprehensive warranty in the industry. In the event of a defect, we cover not only the repair or replacement of the TempZone™ system, but ALSO any labor costs AND flooring materials required to perform the repair. We do not cover the cost of flooring that needs to be replaced in the event of a repair necessitated due to damage. If a product is damaged by a power surge, that would not be covered by our warranty

5 people found this helpful Was this helpful? Yes No

Waterproofing for the room is in the layer above the floor heating system. The layers for waterproofing this type of floor are:

  • subfloor
  • thinset
  • uncoupling membrane
  • tempzone heating cable
  • waterproofing tape for seams and corners
  • thinset or self leveling cement
  • tile floor
5 people found this helpful Was this helpful? Yes No

One thermostat can control multiple heating mats/cables as long as all the heating elements are using less than 15 amps:

TempZone™ will cover aprx. 120 sq. ft. for 120V systems and 240 sq. ft. for 240V systems on one thermostat.

Environ™ will cover aprx. 150 sq. ft. for 120V systems and 300 sq. ft. for 240V systems on one thermostat.

Slab Heat will cover aprx. 90 sq. ft. for 120V systems and 180 sq. ft. for 240V systems on one thermostat.

5 people found this helpful Was this helpful? Yes No

No. Never cut the heating cable. The floor heating cable is designed with a very specific resistance in order to consistently maintain heating at the chosen wattage per square foot. Trimming the heating cable would lower the resistance of the cable causing the system to overheat. Adding heating cable to the system would raise the resistance and the system would not heat properly.

4 people found this helpful Was this helpful? Yes No

Our TempZone electric floor heating products are waterproof and wet location listed.

3 people found this helpful Was this helpful? Yes No

In theory, it is possible, if no other options are available. We do not recommend it, but If the thermostat is controlling the floor temperature with a floor sensor, then it can go on an exterior wall. It is important that the floor sensor gets located in an area of the floor not hit by sunshine.

If the thermostat will be controlling the air temperature with the built-in ambient sensor, then it should go on an interior wall.

3 people found this helpful Was this helpful? Yes No

WarmlyYours has recently begun including floor sensors with our heating elements to help ensure customers will have everything they need for optimal operation of their radiant heating systems.

The sensor included with your floor heating element can be installed with the heating system (the sensor is equally spaced between runs of the heating wire--see your install manual for more info). Installing this sensor with your floor heating control will enable energy efficient operation of the floor warming system based on the floor temperature instead of the ambient room temperature.

We generally recommend that you install a second, unconnected backup floor sensor alongside the primary one. In the very unlikely event that your first floor sensor is damaged, this install method will save you from having to pry up flooring to replace a floor sensor. You simply disconnect the damaged sensor from the thermostat and connect the backup sensor.

In addition to the floor sensor that was included with your heating element, our nSpiration Series thermostats also come with a floor sensor. If you purchase both a heating element and an nSpiration Series thermostat from WarmlyYours, you'll have a primary and a backup floor sensor for your system.

3 people found this helpful Was this helpful? Yes No

Make sure any cracks or raised edges are sanded down before installation. Seal and patch cracks where possible. If needed, pour a layer of self-leveling cement to make sure surface is level and flat. Then proceed with instructions to install desired floor heating system and flooring.


It is strongly recommended that an insulating underlayment be installed between the slab and heating element to prevent heat loss.

2 people found this helpful Was this helpful? Yes No

The ground wire in the floor mat must be connected directly to the ground wire of the supply or to the house ground wire.

2 people found this helpful Was this helpful? Yes No

The TempZone™ twin conductor cable present in our TempZone™ products is comprised of a double-insulated, coaxial heating cable. The total thickness of the system can be between ⅛” and 5/32” thick and will not noticeably affect the height of your installed flooring.

1 person found this helpful Was this helpful? Yes No

Yes, the sensor wires may be trimmed.  Most local code requirements call for 6“-7“ of extra wire from the gang box.

1 person found this helpful Was this helpful? Yes No

WarmlyYours recommends running the floor heating system in F (Floor) mode for most homes. This provides the most efficient operation of the floor heating system and the best protection for the floor covering material that has been installed.

1 person found this helpful Was this helpful? Yes No

Resistance greater than this value may result in overheating or even total failure of the floor heating system. This may be caused by a crimping or other damage to the wire.

1 person found this helpful Was this helpful? Yes No

The wire spacing in the Prodeso Cable Installation Membrane is 3.75“, or every 3rd peg.

1 person found this helpful Was this helpful? Yes No

82°F - 85°F is the most common comfortable warm temperature of the floor.

1 person found this helpful Was this helpful? Yes No

Yes, we offer several options to help make your floor heating system water resistant or waterproof. Our TempZone product line is designed for wet areas - making it completely safe for rooms that will have water on the floor at times or may experience leaks or flooding. We also offer waterproofing bands for our TempZone Cable + Prodeso Uncoupling Membrane system. Allowing you to waterproof all seams and the perimeters of the wall - guaranteeing that your floor heating system stays safe and prevents water from leaking to areas below.

Was this helpful? Yes No

A digital meter with a 0-200 Ohms scale ( Ω ) to measure the heating wire's resistance, and a 20K scale to measure the sensor's resistance.

Was this helpful? Yes No

All thermostats are mandated at 42" height for handicap accessibility, most private residences are mounted at 52-60".

Please see this video on how to install a WarmlyYours nSpiration Series thermostat.

Was this helpful? Yes No

Never cut, shorten or splice the heating cable itself; cutting it damages the system. Only the non-heating cold lead can be shortened, as your product’s manual allows. Order the size your SmartPlan™ specifies, because unused cable can’t be cut off.

Some mats let you cut the mesh, never the cable, to turn or reposition them: TempZone™ and Environ™ Flex Rolls and Slab Heat mats. TempZone™ Easy Mats and Custom Mats are made to size and must not be shortened or cut. TempZone™ Cable has no mesh: lay all of it at the spacing on your SmartPlan™.

Was this helpful? Yes No

Yes, we recommend using the Tempzone system encased in ⅜“-½“ of self-leveling cement followed by LVT.

Was this helpful? Yes No

Yes. The finish layer needs to be 1/2" thick. This can be done if the brand of Self-Leveling Cement (SLC) is engineered to be a final flooring surface.  Most SLC products aren't designed to be the finish surface.

Was this helpful? Yes No

No separate GFCI breaker is required — every WarmlyYours thermostat has a built-in Class A (5mA) GFCI. Stacking a GFCI breaker on top of it is one of the most common causes of nuisance tripping. Run a dedicated breaker sized to the load at 80% continuous duty: a 15A circuit carries up to 1,440W at 120V, a 20A circuit up to 1,920W. Loads beyond the thermostat’s 15A rating need a power module or relay.

Was this helpful? Yes No

Turn the power (circuit breaker typically) to the thermostat off for 5 minutes and then back on to reset the thermostat.

If there is power to the thermostat and it still doesn't appear to work, then the next step toward a solution is to take Ohm measurements of the floor heating system.

This is done with a digital multi-meter that can select a low 200 Ohm (Ω) scale. To conduct this test, turn off the circuit breaker. Remove the thermostat completely from the wall and disconnect the wires connected to the LOAD connections at the back of the thermostat. Disconnect the ground wires from the house ground, and do the test shown on the links below. If you are uncomfortable doing this test, contact a qualified electrician.

Please follow one of these guides based on the type of heating system installed:

TempZone Single Conductor

TempZone Twin Conductor

For a quick overview of the testing process:

Here is a video showing how the test is done

Here is a video showing how to locate and identify the floor heating wires

If the system still does not function, contact +1 (800) 875-5285 WarmlyYours Technical Support and provide the Ohm measurements for further assistance.

Was this helpful? Yes No

Single Conductor vs. Twin Conductor Identification

  • A single conductor floor heating system is a loop of one core wire, it starts at the thermostat and ends at the thermostat - this is the original method of manufacturing heating cable. Most single conductor floor heating systems have the same color cold lead wire connected to both load terminals/pigtails of the thermostat. Some early single conductor floor heating systems were produced with a white and a yellow cold lead wire.
  • A twin conductor floor heating system terminates two core wires at the end, both wires start at the thermostat - this is the current method of manufacturing heating cable. Most twin conductor floor heating systems will have two different colored cold lead wires, and one of these is black. The other wire in a WarmlyYours floor heating system is either yellow (120V system) or red (240V system).  A few early Environ systems had two black cold lead wires.

Note:

- Not all heating cables are wired directly to the thermostat. It may have been necessary during installation to terminate the heating cable in a junction box, and then run a separate (contractor-supplied) wire from the junction box to the thermostat.

- WarmlyYours single conductor cold leads were produced with a 13‘ length at the start of the loop, and a 26‘ length at the end.  The 120V floor heating systems had a yellow and a white label attached to the cold leads, and the 240V floor heating systems had a red and a white label attached. 

- If you have a single conductor floor heating system and notice that one cold lead is thicker or feels hotter than the other, please contact technical support at +1 (800) 875-5285 

Was this helpful? Yes No

Test the TempZone floor heating cable using a digital ohm meter as shown here.

Was this helpful? Yes No

Both are 15 feet long.

Was this helpful? Yes No

One watt equals about 3.412 BTU per hour. TempZone™ Flex Rolls, Easy Mats and Shower Mats, and TempZone™ Cable at 3-inch spacing, deliver 15 watts per square foot: about 51 BTU per hour for every square foot of heated floor. Environ™ delivers 12 watts per square foot, about 41 BTU per hour. For any product, multiply the wattage on its label by 3.412.

Only heated floor counts, and heating can’t run under cabinets or fixtures: 100 square feet of 15-watt heating produces about 5,100 BTU per hour. Compare that with your room’s heat loss.

Was this helpful? Yes No

TempZone™ Flex Rolls, Easy Mats and Shower Mats deliver 15 watts per square foot, and Custom Mats 12 to 15. TempZone™ Cable and Ruler Cable deliver 3.7 watts per linear foot, so their output depends on spacing: about 15 watts per square foot at 3 inches, 11 at 4 and 9 at 5. See TempZone Cable spacing and attachment.

Was this helpful? Yes No

A variance of +/- 15% is acceptable.

Was this helpful? Yes No

For the same wattage and operating time, 120V and 240V electric floor heating use the same amount of energy and produce the same heat. A 240V system draws less current for the same wattage, which can accommodate a larger heated area on a suitable circuit. Choose the heating product and control voltage to match the supply, and have an electrician verify circuit capacity, wiring, and applicable code.

Was this helpful? Yes No

Check these common causes:

  • Trapped heat: a heavy or rubber-backed rug or furniture over the sensor makes it read high. Move the item.
  • Two sensors connected: disconnect the extra sensor and leave one pair of wires on terminals C+D.
  • Changed calibration: this setting should never be changed. Do a factory reset (Installer and User resets).
  • Older system: some older systems, especially those with an OJ Dual/Energystat thermostat, used 12kΩ sensors. Change the installer setting from the default 10kΩ to 12kΩ.

Need more help? Contact WarmlyYours technical support.

Was this helpful? Yes No

An uncoupling membrane like Prodeso provides a flexible layer between your subfloor and tile, preventing cracks caused by natural floor movement. It also offers waterproofing and vapor management, making it ideal for bathrooms. Plus, the membrane’s studs make cable installation fast and consistent without the need for staples or glue.

Was this helpful? Yes No

Resistance below this value may result in no heating or cold spots in the floor. This may be caused by exposure to moisture or other conductive material that penetrates the core insulation.

Was this helpful? Yes No

That is the sound the thermostat makes when the relay is either opened or closed to turn on or off the power to the floor heating elements. See this article for further information.

Was this helpful? Yes No

Pricing for TempZone Cable heating product typically starts at $6 per sq. ft. ($7 CAD) when installed with Fixing Strips and $9 per sq. ft. ($11 CAD) when installed with our Prodeso Cable Installation Membrane. 

Was this helpful? Yes No

In TempZone™ Flex Rolls, Easy Mats and Shower Mats, the heating cable is fixed 3 inches apart. Custom Mats follow each design. TempZone™ Cable and Ruler Cable are spaced as you install them: 3, 4 or 5 inches on GripStrips™, or set by the membrane, and never closer than 3 inches. See TempZone Cable spacing and attachment.

Was this helpful? Yes No

WarmlyYours controllers incorporate built-in Class A GFCI protection for all new floor heating systems.  Class A GFCI provides personnel protection and trips when ground fault current exceeds 5 mA (milliamps).  Class B GFCI protection is pretty much obsolete, but older systems may still require it.  WarmlyYours controllers with built-in Class B GFCI provide equipment and circuit protection and operates when a fault to ground exceeds 15 mA.

Was this helpful? Yes No

The amount of amperage draw depends upon how large the area is that you are heating. For coverage of areas less than 30 square feet, a 120V TempZone system will draw less than 4 amps. If you have a larger area over 240 square feet of heated space, then you will need a larger breaker plus additional controls. No matter what the size of the area you choose to heat, we recommend a dedicated circuit for your electric radiant floor heating system.

Was this helpful? Yes No

For systems below 12 Amps, a 15 Amp, Non-GFI breaker is fine. For systems 12 to 16 Amps, a 20 Amp, non-GFI breaker is needed. Breaker sizes are noted on the installation plan that ships with many orders.

Was this helpful? Yes No

Keep the power lead factory splice and the cable end seal outside the shower area and at least 1 ft. away from shower openings or other spots normally exposed to water. The control must be located at least 4 ft. from shower openings, where it cannot be exposed to water or touched by someone in the shower.

Was this helpful? Yes No

Temperature affects core resistance - lower temperatures decrease resistance and higher temperatures increase resistance. Another consideration is the test equipment, sometimes switching test units, adjusting the calibration, or allowing for the verified differential may be necessary.

Was this helpful? Yes No

More output lets the floor make up more of a room’s heat loss. TempZone™ Flex Rolls, Easy Mats and Shower Mats, and TempZone™ Cable at 3-inch spacing, deliver 15 watts per square foot: up to 25% more heating power than the nearest competitor’s systems, and enough for primary or supplemental heat. Cable at 4-inch spacing, about 11 watts per square foot, is for supplemental heat only.

Whether floor heating can be a room’s only heat source depends on that room’s heat loss. An uninsulated concrete slab, for example, absorbs part of the heat, so insulating over it helps. WarmlyYours can calculate your room’s heat loss before you decide.

Was this helpful? Yes No

A floor sensor measures floor temperature so a compatible thermostat can regulate comfort and enforce the flooring manufacturer’s temperature limit. Some thermostats, including nTrust 2.0, offer a regulator mode without a sensor, but that mode does not measure floor temperature. Use sensor-based temperature control whenever required by the flooring or heating-system instructions.

Was this helpful? Yes No

Documents

Technical Support

Installation

Project Planners

Publications

Technical Information

Sell Sheets

Technical Specifications

Operation Manuals

Warranties

Register Warranty

Wiring Diagrams

Specifications

Electrical (TCT240-3.7W-235)

Amps 3.78 A
Cold Lead Wire Gauge 17 AWG
Floor Load 0.91 kW
Ohms 63.55 Ω
Ohms Per Ft 0.27 Ohm/ft
Thermal Power 0.91 kW
Voltage 240 V
Watts 906 W
Watts Per Sq. Ft at 3.75 Inch Spacing Up to 12
Watts Per Sq. Ft. 9 to 15
Watts Per Sq. Ft. at 3 Inch Spacing Up to 15
Watts Per Sq. Ft. at 4 Inch Spacing Up to 11
Watts Per Sq. Ft. at 5 Inch Spacing Up to 9

Warranty / Certifications (TCT240-3.7W-235)

Approvals cULus listed
Warranty 25 Year Warranty
Wet Location Listed US, Canada

Warranty / Certifications (UTN5-4999)

Approvals cULus listed
Ingress Protection (IPxx) Rating IP20
Warranty Limited 3-year warranty and lifetime technical support

Performance (TCT240-3.7W-235)

BTU Per Hour 3091 Btu

Electrical (UTN5-4999)

Battery No battery inside; confirmed by OJ Electronics
Connection 4 wires, double pole, screw terminals
Connection Method Hardwired
Ground Fault Protection GFCI, Class A, 5 mA
Maximum Current 15 A
Maximum Power 1800 W @ 120 V, 3120 W @ 208 V, 3600 W @ 240 V
Power Terminal Wire Gauge 14–12 AWG solid or stranded; 14–13 AWG stranded with ferrule
Signal Terminal Wire Gauge 22–18 AWG solid or stranded; 22–20 AWG stranded with ferrule
Supply 120 VAC, 208 VAC, 240 VAC (50/60Hz)

Product Dimensions (TCT240-3.7W-235)

Cold Lead Length 15′
Coverage 78.3 ft²
Coverage at 3 Inch Spacing 58.8 ft²
Coverage at 3.5 Inch Spacing 68.5 ft²
Coverage at 3.75 Inch Spacing 73.4 ft²
Coverage at 4 Inch Spacing 78.3 ft²
Coverage at 5 Inch Spacing 97.9 ft²
Heating Cable Length 235′
Heating Element Thickness 3/16″
Length 235′
Weight 7.8 lbs

Appearance (TCT240-3.7W-235)

Color Red

Appearance (UTN5-4999)

Color White Acrylic
Display LED Light Through

Product Dimensions (UTN5-4999)

Depth 1.73″
Installed Depth 0.46″
Length 4.98″
Weight 0.6 lbs
Width 3.09″

Installation (TCT240-3.7W-235)

Fixing Strips at 3 inch spacing 60
Fixing Strips at 4 inch spacing 60
Fixing Strips at 5 inch spacing 80
Floor Types Commonly installed beneath tile and stone
Ideal Cable Spacing with Competitor's Membrane 3½″
Ideal Cable Spacing with Fixing Strips 4″
Ideal Cable Spacing with Prodeso Membrane 3¾″

Thermostat (UTN5-4999)

Floor Sensor Compatibility 10k ohms or 12k ohms
Includes Floor Sensor 10k ohms, 15′ lead
Maximum Ambient Temperature Setting 77 °F
Maximum Floor Temperature Setting 104 °F
Minimum Ambient Temperature Setting 32 °F
Minimum Floor Temperature Setting 41 °F

Logistics (TCT240-3.7W-235)

Package Contents (1) TempZone Floor Heating Cable 240V 3.7W/ft 235 ft 3.7A (TCT240-3.7W-235); 1x Floor Heating Sensor (FH-BACKUP-SENSOR)
UNSPSC Code 40101830

Identifiers (TCT240-3.7W-235)

SKU TCT240-3.7W-235
UPC (GTIN-12) 881308049164

Identifiers (UTN5-4999)

SKU UTN5-4999
UPC (GTIN-12) 881308080426

Similar Items

Do you need support or specifications for a specific model? Identify your model below.

TCT120-KIT-UTN5-MEM-030

TempZone Cable Kit 30 ft (9.4 sqft @ 3.75 in spacing) with nTrust 2.0 Touch Nonprogrammable Thermostat, Uncoupling Membrane, 120V, 3.7/ft, 1.08A

TCT120-KIT-UTN5-MEM-040

TempZone Cable Kit 40 ft (12.5 sqft @ 3.75 in spacing) with nTrust 2.0 Touch Nonprogrammable Thermostat, Uncoupling Membrane, 120V, 3.7/ft, 1.24A

TCT120-KIT-UTN5-MEM-050

TempZone Cable Kit 50 ft (15.6 sqft @ 3.75 in spacing) with nTrust 2.0 Touch Nonprogrammable Thermostat, Uncoupling Membrane, 120V, 3.7/ft, 1.54A

TCT120-KIT-UTN5-MEM-070

TempZone Cable Kit 70 ft (21.9 sqft @ 3.75 in spacing) with nTrust 2.0 Touch Nonprogrammable Thermostat, Uncoupling Membrane, 120V, 3.7/ft, 2.24A

TCT120-KIT-UTN5-MEM-090

TempZone Cable Kit 90 ft (28.1 sqft @ 3.75 in spacing) with nTrust 2.0 Touch Nonprogrammable Thermostat, Uncoupling Membrane, 120V, 3.7/ft, 2.83A

TCT120-KIT-UTN5-MEM-120

TempZone Cable Kit 120 ft (37.5 sqft @ 3.75 in spacing) with nTrust 2.0 Touch Nonprogrammable Thermostat, Uncoupling Membrane, 120V, 3.7/ft, 3.7A

TCT120-KIT-UTN5-MEM-150

TempZone Cable Kit 150 ft (46.9 sqft @ 3.75 in spacing) with nTrust 2.0 Touch Nonprogrammable Thermostat, Uncoupling Membrane, 120V, 3.7/ft, 4.78A

TCT120-KIT-UTN5-MEM-180

TempZone Cable Kit 180 ft (56.3 sqft @ 3.75 in spacing) with nTrust 2.0 Touch Nonprogrammable Thermostat, Uncoupling Membrane, 120V, 3.7/ft, 5.65A

TCT120-KIT-UTN5-MEM-220

TempZone Cable Kit 220 ft (68.8 sqft @ 3.75 in spacing) with nTrust 2.0 Touch Nonprogrammable Thermostat, Uncoupling Membrane, 120V, 3.7/ft, 6.82A

TCT120-KIT-UTN5-MEM-260

TempZone Cable Kit 260 ft (81.3 sqft @ 3.75 in spacing) with nTrust 2.0 Touch Nonprogrammable Thermostat, Uncoupling Membrane, 120V, 3.7/ft, 8.18A

TCT120-KIT-UTN5-MEM-300

TempZone Cable Kit 300 ft (93.8 sqft @ 3.75 in spacing) with nTrust 2.0 Touch Nonprogrammable Thermostat, Uncoupling Membrane, 120V, 3.7/ft, 9.35A

TCT120-KIT-UTN5-MEM-340

TempZone Cable Kit 340 ft (106.3 sqft @ 3.75 in spacing) with nTrust 2.0 Touch Nonprogrammable Thermostat, Uncoupling Membrane, 120V, 3.7/ft, 10.52A

TCT120-KIT-UTN5-MEM-375

TempZone Cable Kit 375 ft (117.2 sqft @ 3.75 in spacing) with nTrust 2.0 Touch Nonprogrammable Thermostat, Uncoupling Membrane, 120V, 3.7/ft, 11.63A

TCT120-KIT-UTN5-MEM-432

TempZone Cable Kit 432 ft (135 sqft @ 3.75 in spacing) with nTrust 2.0 Touch Nonprogrammable Thermostat, Uncoupling Membrane, 120V, 3.7/ft, 13.48A

TCT240-KIT-UTN5-MEM-055

TempZone Cable Kit 55 ft (17.2 sqft @ 3.75 in spacing) with nTrust 2.0 Touch Nonprogrammable Thermostat, Uncoupling Membrane, 240V, 3.7/ft, 0.95A

TCT240-KIT-UTN5-MEM-065

TempZone Cable Kit 65 ft (20.3 sqft @ 3.75 in spacing) with nTrust 2.0 Touch Nonprogrammable Thermostat, Uncoupling Membrane, 240V, 3.7/ft, 1.21A

TCT240-KIT-UTN5-MEM-075

TempZone Cable Kit 75 ft (23.4 sqft @ 3.75 in spacing) with nTrust 2.0 Touch Nonprogrammable Thermostat, Uncoupling Membrane, 240V, 3.7/ft, 1.24A

TCT240-KIT-UTN5-MEM-095

TempZone Cable Kit 95 ft (29.7 sqft @ 3.75 in spacing) with nTrust 2.0 Touch Nonprogrammable Thermostat, Uncoupling Membrane, 240V, 3.7/ft, 1.53A

TCT240-KIT-UTN5-MEM-115

TempZone Cable Kit 115 ft (35.9 sqft @ 3.75 in spacing) with nTrust 2.0 Touch Nonprogrammable Thermostat, Uncoupling Membrane, 240V, 3.7/ft, 1.83A

TCT240-KIT-UTN5-MEM-155

TempZone Cable Kit 155 ft (48.4 sqft @ 3.75 in spacing) with nTrust 2.0 Touch Nonprogrammable Thermostat, Uncoupling Membrane, 240V, 3.7/ft, 2.41A

TCT240-KIT-UTN5-MEM-195

TempZone Cable Kit 195 ft (60.9 sqft @ 3.75 in spacing) with nTrust 2.0 Touch Nonprogrammable Thermostat, Uncoupling Membrane, 240V, 3.7/ft, 3.19A

TCT240-KIT-UTN5-MEM-275

TempZone Cable Kit 275 ft (85.9 sqft @ 3.75 in spacing) with nTrust 2.0 Touch Nonprogrammable Thermostat, Uncoupling Membrane, 240V, 3.7/ft, 4.36A

TCT240-KIT-UTN5-MEM-315

TempZone Cable Kit 315 ft (98.4 sqft @ 3.75 in spacing) with nTrust 2.0 Touch Nonprogrammable Thermostat, Uncoupling Membrane, 240V, 3.7/ft, 4.94A

TCT240-KIT-UTN5-MEM-355

TempZone Cable Kit 355 ft (110.9 sqft @ 3.75 in spacing) with nTrust 2.0 Touch Nonprogrammable Thermostat, Uncoupling Membrane, 240V, 3.7/ft, 5.53A

TCT240-KIT-UTN5-MEM-395

TempZone Cable Kit 395 ft (123.4 sqft @ 3.75 in spacing) with nTrust 2.0 Touch Nonprogrammable Thermostat, Uncoupling Membrane, 240V, 3.7/ft, 6.11A

TCT240-KIT-UTN5-MEM-435

TempZone Cable Kit 435 ft (135.9 sqft @ 3.75 in spacing) with nTrust 2.0 Touch Nonprogrammable Thermostat, Uncoupling Membrane, 240V, 3.7/ft, 6.89A

TCT240-KIT-UTN5-MEM-515

TempZone Cable Kit 515 ft (160.9 sqft @ 3.75 in spacing) with nTrust 2.0 Touch Nonprogrammable Thermostat, Uncoupling Membrane, 240V, 3.7/ft, 8.06A

TCT240-KIT-UTN5-MEM-595

TempZone Cable Kit 595 ft (185.9 sqft @ 3.75 in spacing) with nTrust 2.0 Touch Nonprogrammable Thermostat, Uncoupling Membrane, 240V, 3.7/ft, 9.23A

TCT240-KIT-UTN5-MEM-675

TempZone Cable Kit 675 ft (210.9 sqft @ 3.75 in spacing) with nTrust 2.0 Touch Nonprogrammable Thermostat, Uncoupling Membrane, 240V, 3.7/ft, 10.59A

TCT240-KIT-UTN5-MEM-749

TempZone Cable Kit 749 ft (234.1 sqft @ 3.75 in spacing) with nTrust 2.0 Touch Nonprogrammable Thermostat, Uncoupling Membrane, 240V, 3.7/ft, 11.65A

TCT240-KIT-UTN5-MEM-864

TempZone Cable Kit 864 ft (270 sqft @ 3.75 in spacing) with nTrust 2.0 Touch Nonprogrammable Thermostat, Uncoupling Membrane, 240V, 3.7/ft, 13.4A

Speak to a radiant heating expert

Can’t find what you’re looking for? Create a Support Request